MP2720A

MP2720A

2.2A, Single-Cell Buck Charger with 15mA Termination Current

Datasheet

Description

The MP2720A is a highly integrated, 2.2A switch-mode battery management device for single-cell Li-ion or Li-polymer batteries. The narrow-voltage DC (NVDC) power management structure provides a low impedance power path that optimizes charging efficiency, reduces battery charging time, and extends battery life during discharging.

The MP2720A’s input source type identification algorithm supports USB battery charging specification 1.2 (BC1.2) and non-standard adapter detection. The serial interface offers complete operating control, including charging parameter configurations and status/interrupt monitoring.

The MP2720A supports a fully customizable JEITA profile with configurable temperature windows and actions.

The MP2720A is available in a QFN-22 (2.5mmx3.5mm) package.

Features & Benefits

2.2A Switching Charger with Narrow Voltage DC (NVDC) Power Path Management
Supports USB BC1.2 and Non-Standard Adapters
26V Sustainable Input Voltage (V_IN)
Configurable 40mA to 2.2A Charge Current (I_CC) via the Serial Interface
Configurable 100mA to 3.2A Input Current Limit (I_{IN_LIM}) via the Serial Interface
Minimum V_IN Loop for Maximum Adapter Power Tracking
Comprehensive Safety Features:
- Fully Customizable JEITA Profile
- Additional Negative Temperature Coefficient (NTC) Thermistor Input
- Configurable Die Temperature Regulation from 60°C to 120°C
- Complete Charge and Pre-Charge Safety Timers
- Watchdog Safety Timer
- Lockable Registers for Charging Parameters
Configurable 750kHz to 1.5MHz Switching Frequency (f_SW)
Integrated 30mΩ Low On Resistance (R_DS(ON)) Battery MOSFET with Shipping and Reset Modes

Ultra-Low 8.5μA Battery Discharge Current in Shipping Mode

Down to 15mA Termination Current Settings for Wearable Applications

Serial Interface Port for Flexible System Parameter Setting and Status Reporting

Configurable Boost Converter for Source Mode and USB On-The-Go (OTG):

Configurable Output Current Limit Loop Up to 3A
Output Over-Current Protection (OCP)
Ability to Power into Large Capacitive Loads Up to 2mF
Configurable 5V to 5.35V Output Voltage (V_OUT)

Accuracy:

±0.5% Battery Regulation Voltage (V_{BATT_REG})
±5% I_CC
±5% I_{IN_LIM}
Remote Battery Sensing for Fast Charge
±2% Output Regulation in Boost Mode

Available in a Small QFN-22(2.5mm×3.5mm) Package

Active Part Numbers:

MP2720AGRH-xxxx-Z MP2720AGRH-xxxx-P MP2720AGRH-0000-Z MP2720AGRH-0000-P

Meaning of P & Z

Related Products

EV2720A-RH-00A Single-Cell, 2.2A Buck Charger with 15mA Termination Current Evaluation Board with Serial Interface Control

The EV2720A-RH-00A is an evaluation board designed to demonstrate the capabilities of the MP2720A, a highly integrated, 2.2A, switch-mode battery management device for single-cell Li-ion or Li-polymer batteries, with a termination current as low as 15mA. The narrow-voltage DC (NVDC) power management structure provides a low-impedance power path that optimizes charging efficiency, reduces battery charging time, and extends battery life during discharging.

USB Battery Charging Specification 1.2 (BC 1.2) and non-standard adapter detection are supported by the input source type identification algorithm. The serial interface provides complete operating control, charging parameter configurations, and status/interrupt monitoring. The MP2720A supports a fully customizable JEITA profile with configurable temperature windows and actions.

The EV2720A-RH-00A supports an operating voltage up to 6.3V. It also supports boost mode and USB On-The-Go (OTG) operation by supplying a voltage between 5V and 5.35V at the IN pin.

$50.00
+ tax